Linear Products Knowledge Base

Scenario 1-Using the optional IEI USB to Serial Converter on Single Gang Plate (P/N 0295097)

1.   Connect the USB cable to any USB port on your computer.

2.   Connect the other end of the USB cable to the USB to Serial Converter on Single Gang Plate.

3.   Windows will recognize this device and prompt you to install the driver.  Follow the onscreen prompts to install the driver for this device.  Information about the location of the driver is located on the first page of the manual included with the USB to Serial Converter.  When properly installed it will be listed as a USB Serial Port.

4.   Use the Windows device manager to verify which Com Ports are recognized by the computer and note which Com Port the USB Serial Port occupies.  If the Com Port to be used with HubManager Pro occupies any Com Port above Com8, change the settings for that Com Port to be between 1 and 8.

5.   Connect the Black, Red and Gray wires from the USB to Serial Converter to the P5 wiring harness included with the ProxPadPlus in the following manner.

USB to Serial Converter    ----      ProxPadPlus P5 Connector

Black                                                  Green

Red                                                     White

Gray                                                    Brown

6.   Create a site in HubManager Pro and select the following settings.

Name                                                 Site name of your choosing

Device Group                                  Max3, ProxPadPlus

Connection Type                           Serial

7.   On the Serial Parameters tab choose the Comm port you noted in step 4.

8.   Run the Com Port Test on the Serial Parameters tab of your site addition screen to verify that the com port you have chosen is "Available for use".   Unless you suspect a problem with your Com Port, it is not necessary to run the Loop Back test.

9.   Save your site.

10. Verify that the Local/Remote switch on the backplane is set to Local.

11. Each ProxPadPlus must be numbered.  See the programming manual for instructions on numbering the ProxPadPlus.  After completion of this step, go to the Communications Menu and choose Network Query.

12. Press Start and the HubManager Program will discover and add your doors.

Scenario 2-Using the optional IEI 232-485 Converter (P/N 0295093)

1.   Connect the IEI supplied ToComp (P/N E000-0004) Adapter to the Communications Port (Com Port) on your computer.

2.   Connect the IEI supplied phone type cable to the ToComp Adapter.

3.   Connect the other end of the phone type cable to the RJ11 connector labeled RS232 on the front of the IEI 232-485 Converter.

4.   Connect 12-24 Volts AC or DC to the 232-485 Converter.

5.   Connect the 232-485 Converter to the ProxPadPlus P5 wiring harness included with the ProxPadPlus in the following manner.

232-485 Converter                         ----       ProxPadPlus P5 Connector

GND                                                               Green

B                                                                     White

A                                                                     Brown

6.   Create a site in HubManager Pro and select the following settings.

Name                                                 Site name of your choosing

Device Group                                  Max3, ProxPadPlus

Connection Type                           Serial

7.   Use the Windows device manager to verify which Com Ports are recognized by the computer.  Note the Com Port number for the port you plugged the ToComp Adapter into.  If the Com Port to be used with HubManager Pro occupies any Com Port above Com8, change the settings for that Com Port to be between 1 and 8.

8.   On the Serial Parameters tab choose the Com port you noted in step 7.

9.   Run the Com Port Test on the Serial Parameters tab of your site addition screen to verify that the com port you have chosen is "Available for use".   Unless you suspect a problem with your Com Port, it is not necessary to run the Loop Back test.

10. Save your site.

11. Verify that the Local/Remote switch on the backplane is set to Local.

12. Each ProxPadPlus must be numbered.  See the programming manual for instructions on numbering the ProxPadPlus.  After completion of this step, go to the Communications Menu and choose Network Query.

13. Press Start and the HubManager Program will discover and add your doors.