Your changes will require approval by an administrator before they are published.
The article has been updated successfully but requires approval before it is published.1. Connect the IEI -supplied ToComp (P/N E000-0004) Adapter to the Communications Port (Com Port) on your computer.
2. Connect the IEI-supplied phone type cable to the ToComp adapter.
3. Connect the other end of the IEI-supplied phone type cable to the RJ11A connector on the back plane of the Max2/MiniMax2 panel.
4. Verify that the Local/Remote switch on the backplane is set to Local.
5. Use the Windows device manager to verify which Com Ports are recognized by the computer. If it is a
built-in Com Port, it will probably be Com1. Take note of which Com Port you plugged the adapter into.
6. If you are using a USB to RS-232 Serial adapter, be sure the driver has been installed according to the manufacturer's instructions. Note which Com Port it occupies. If the Com Port to be used with HubManager Pro occupies any Com Port above Com8, change the settings for that Com Port to be between 1 and 8.
7. Create a site in HubManager Pro and select the following settings.
Name Site name of your choosing
Device Group HC500, Hub+, HubMax, Max2
Connection Type Serial
8. On the Serial Parameters tab choose the Com Port you noted in step 5 or 6, depending on your computer configuration.
9. Run the Com Port Test on the Serial Parameters tab of the site addition screen to verify that the Com Port you have chosen is "Available for use". Unless you suspect a problem with your Com Port, it is not necessary to run the Loop Back test.
10. Save your site.
11. Each Door Control Module must be numbered. See the programming manual for instructions on numbering the Door Control Modules. After completion of this step, go to the Communications Menu and choose Network Query.
12. Press Start and the HubManager Program will discover and add your doors.
Scenario 2-The PC is more than 6' from the Panel and using the included PC Software Assembly Kit (P/N 2085010)
1. Connect the IEI-supplied ToComp (P/N E000-0004) Adapter to the Communications Port (Com Port) on your computer.
2. Connect the IEI-supplied phone type cable to the ToComp adapter.
3. Connect the IEI-supplied phone type cable to the IEI-supplied Phone Jack Junction Box.
4. Verify that the Local/Remote switch on the backplane is set to Local.
5. Connect the Phone Jack Junction Box to TS1 on the back plane using the following connections.
Junction Box ----- TS1
Green GND
Red A0
Black A1
6. Use the Windows device manager to verify which Com Ports are recognized by the computer. If it is a
built-in Com Port it will probably be Com1. Take note of which Com Port you plugged the adapter into.
7. If you are using a USB to RS-232 Serial adapter, be sure the driver has been installed according to the manufacturer's instructions. Note which Com Port it occupies. If the Com Port to be used with HubManager Pro occupies any Com Port above Com8, change the settings for that Com Port to be between 1 and 8.
8. Create a site in HubManager Pro and select the following settings.
Name Site name of your choosing
Device Group HC500, Hub+, HubMax, Max2
Connection Type Serial
9. On the Serial Parameters tab, choose the Com Port you noted in step 6 or 7.
10. Run the Com Port Test on the Serial Parameters tab of your site addition screen to verify that the Com Port you have chosen is "Available for use". Unless you suspect a problem with your Com Port, it is not necessary to run the Loop Back test.
11. Save your site.
12. Each Door Control Module must be numbered. See the programming manual for instructions on numbering the Door Control Modules. After completion of this step, go to the Communications Menu and choose Network Query.
13. Press Start and the HubManager Program will discover and add your doors.
Scenario 3 Using the optional IEI USB to Serial Converter on Single Gang Plate (P/N 0295097)
1. Connect the USB cable to any USB port on your computer.
2. Connect the other end of the USB cable to the USB to Serial Converter.
3. Windows will recognize this device and prompt you to install the driver. Follow the onscreen prompts to install the driver for this device. Information about the location of the driver is located on the first page of the manual included with the USB to Serial Converter.
4. Use the Windows device manager to verify which Com Port Windows has been assigned to the USB to Serial Converter. It will be designated as a USB Serial Port if properly installed. Note which Com Port the USB Serial Port occupies. If the Com Port to be used with HubManager Pro occupies any Com Port above Com8, change the settings for that Com Port to be between 1 and 8.
5. Verify that the Local/Remote switch on the backplane is set to Local.
6. Create a site in HubManager Pro and select the following settings.
Name Site name of your choosing
Device Group HC500, Hub+, HubMax, Max2
Connection Type Serial
7. On the Serial Parameters tab, choose the Com Port you noted in step 4.
8. Run the Com Port Test on the Serial Parameters tab of your site addition screen to verify that the Com Port you have chosen is "Available for use". Unless you suspect a problem with your Com Port, it is not necessary to run the Loop Back test.
9. Save your site.
10. Connect the Green, Blue and Black wires from the USB to Serial Converter to TS1 on the backplane using the following connections.
USB Converter ---- TS1
Green A1
Blue A0
Black GND
13. Each Door Control Module must be numbered. See the programming manual for instructions on numbering the Door Control Modules. After completion of this step, go to the Communications Menu and choose Network Query.
14. Press Start and the HubManager Program will discover and add your doors.
