Linear Products Knowledge Base

Category » Security

There were 15 articles found in this category:

1. How do I wire a door strike or magnetic lock to my receiver?
   All Linear receivers that use "dry contact" outputs do not supply voltage from the relays. This means that the receiver does not supply the voltage for the door strike or magnetic lock. You will need a power supply that supplies the correct voltage and sufficient current to operate the door s ...
2. Is the DXS-80, CO Detector UL listed?
   Yes, the DXS-80 is UL 2075 / UL 2034 compliant.
3. How do I setup my Extended Range Transmitter and Receiver for Status or Supervisory operation?
   The Extended Range Transmitter can be set to send a Status signal every hour. If the Extended Range Receiver does not receive a Status signal from the correct transmitter, the receiver will activate the Status output on the receiver after 4 hours. The Status option is set by Option Switch 5 on ...
4. How do I wire a strobe light or siren to my receiver?
   All Linear receivers that use "dry contact" outputs do not supply voltage from the relays. This means that the receiver does not supply the voltage for the door strike or magnetic lock. You will need a power supply that supplies the correct voltage and sufficient current to operate the door ...
5. How do I set my extended range transmitter and receiver to work together?
   The System Code that is sent by the Extended Range Transmitter is set using the System Code Switches. The System Code Switches are 2 sets of 8 switch dipswitch packs set side by side on the transmitter board. These dipswitches can be set in any combination of on or off that is desired. The Sy ...
6. How do I set the output to latch on my Extended Range Receiver?
   The output on an Extended Range Receiver can be set to function in one of two ways. It can be set for manual or auto restoral. manual restore is used when you want the output of the Extended Range Receiver to follow the input of the Extended Range Transmitter. This would be a toggle or latc ...
7. How do I program or delete a transmitter in a CP90?
   1. Enter the programming mode by pressing "9", then the Master Code (default: 98765). 2. Press "2", then "???" (the second button down in the left column of buttons. 3. Enter an unused transmitter location. 4. Press the "???" (the second button down in the left column of buttons). 5. Pres ...
8. How do I program a transmitter into a security panel?
   1.Use your Master Code, then hit "Test" button once to go into the Test mode. 2. Use your Master Code and "Test" button again to get into programming. 3.Input the zone number for the transmitter, then activate the transmitter. 4.Hold down the "Off" key to exit programming.
9. How do I arm and disarm my system?
   To arm the system, do the following: Input the Master Code. Hit the "Home" button to go into the Home mode. Input the Master Code. Press the "Away" button to go into the Away mode. Input the Master Code. To disarm the system, do the following: Press "Off" to disarm the system.
10. How do I reset the master code on my security panel?
    Without knowing the master code, you are unable to reset the master password. You can try and dial into the unit with the RA-2400 software and see what the master code is. This can only be done if the remote access password has not been changed from the default 9 8 7 6 5 4.
11. Can I program with a telephone
    All of our security panels can be programmed through a telephone line using a computer and the RA-2400 software, but are unable to be programmed with a regular touch-tone telephone.
12. How do I program a transmitter into a DXR701 and DXR702
    First press and release the Program button. The red program light should remain solid. While the light is solid, activate the transmitter. If the receiver captures the transmitter information, the red program light will flicker, then go out.
13. How do I program a transmitter into a SXR64A?
    1. With the panel disarmed, press the UP or DOWN button until the desired receiver channel number (1-64) is displayed - Memory light will be off if the receiver channel is vacant (only a vacant channel will accept a transmitter 2. Press the ADVANCE button to select the output zone (channel) n ...
14. How do I program a transmitter into a DXSR1504 and DXSR1508
    1. Remove the receiver's cover 2. On the receiver, locate and remove the program jumper 3. Prepare the new remote to send a signal 4. On the receiver, press and release the program button for the desired channel 5. While the channel light is visible in the display, activate the transmitter 6. On ...
15. DXSR-1504/1508 - Factory Default
    Note: This erases all transmitters and resets all parameters to factory defaults. 1.Remove the Program Jumper 2.Remove power for at least ten seconds 3.Press and hold program buttons #1 and #2 4.Apply power 5.Release program buttons #1 and #2 Pressing the program buttons (one at a time) will d ...