Linear Products Knowledge Base

Category » M&S Central Vaccum Systems

There were 21 articles found in this category:

1. My Vacuum won't shut off
   Press and hold the "reset button" for 7 seconds. If it still does not want to shut off, try unplugging the main canister and then plugging it back into the wall. If the unit still does not want to shut off, you may need to contact a local dealer and ask them to service your unit. For a list of ...
2. My Wall inlet has a constant red LED, but my vacuum canister has a green LED.
   The LED's on the wall inlet are designed for use with the ZX and AVP Series of vacuum. The wall outlet LED's should be disregarded if you use any other series of vacuum. If you have a ZX or AVP series vacuum and the wall inlet has a green light that means your unit is working fine. If you recei ...
3. One inlet has good suction, but another one doesn't.
   You probably have an inlet that is clogged, or the section of piping which feeds the inlet has a clog or a break in it. Check the inlet for a clog.If you don't see anything, you may want to call a local dealer for assistance. To find a dealer in your area, please refer to the dealer locator on ...
4. My vacuum doesn't have as much suction as it use to. What's wrong?
   Most central vacuum systems have two filters that protect the motor from dirt and debris – the main cloth bag or sponge filter, and a smaller screen filter. Some older model vacuums employed a sponge filter instead. These older models did not have a secondary filter. When these filters be ...
5. My vacuum won't turn on.
   Check to make sure the electrical outlet that the unit is plugged into is working properly. Try pressing and holding the reset button on the front of the vacuum canister for seven seconds and then release it. Check your circuit breaker to see if your circuit breaker has been tripped. If your va ...
6. How can I find a dealer in my area?
   You can locate a local dealer by visiting our website at http://www.linearcorp.com/locator/ . You can search for a dealer by using the pull-down menu to select your state, or by clicking on the "zip code" link, which allows you to search for dealers by zip codes. If you are unable to locate a de ...
7. How do you remove or install the Teflon bag in my vacuum?
   All of our vacuum canisters have a Teflon filter bag inside the unit which keeps most of the debris away from the motor. This bag may become clogged with dirt and may need to be removed and cleaned in order to keep your vacuum running efficiently. In order to remove this bag, please follow the ...
8. Can I buy wheels for my power brush?
   We do not carry most parts for hoses, wands, or power heads. The only parts available are the belt and light kits for most power heads. If you want to try and fix the brush yourself, you can try going online to locate the part. Please note that any repair work done to a product, outside of that ...
9. Can I replace the cord on my wand?
   We do not carry most parts for hoses, wands, or power heads. The only parts available are the belt and light kits for most power heads. If you want to try and fix the wand yourself, you can try going online to locate the part. Please note that any repair work done to a product, outside of tho ...
10. Can I buy a replacement switch for my hose?
    We do not carry most parts for hoses, wands, or power heads.The only parts available are the belt and light kits for most power heads. If you want to try and fix the hose yourself, you can try going online to locate the part. Please note that any repair work done to a hose, outside of those done ...
11. What is the suction pressure (look up) for my vacuum?
    Your suction rating is measured in Water Lift and Air Flow. For the correct measurement of your AVP or AVR unit, please open the attachment at the bottom of this page. If you have additional questions, feel free to contact us at vacuum@linearcorp.com.
12. Can I vacuum saw dust?
    Yes; however only if you are vacuuming a small amount of shavings from cutting wood. The Air Vac is not designed to vacuum fine dust, large amounts of saw dust or be attached directly to a power tool to be used as a dust collector. If you have any other questions, please feel free to contact ...
13. Can I Vacuum liquid?
    No. Do not use the vacuum to pick up any wet spills of any kind. Electrical shock may occur and you will definitely damage the motor. If you have any other questions, please feel free to contact us via email at vacuum@linearcorp.com.
14. Can I use the bag from any manufacturer?
    No.The use of a non Linear product adversely affects the quality & performance of Linear products. Only Linear approved vacuums bags may be used with Linear equipment. If you have any additional questions, please contact us at vacuum@linearcorp.com.
15. Can I use the hose from any manufacturer?
    No. The use of a non Linear product may adversely affect the quality & performance of your Linear product. Only Linear approved vacuums hoses should be used with your vacuum equipment. If you have any additional questions, please contact us at vacuum@linearcorp.com.
16. If I upgrade my power head, the hose, or the wand, can I keep my old equipment?
    This really depends on several factors: the type of equipment you have, the model that you are currently using, and what you intend to purchase at this time. If you have a "standard" power head (air only, non-electrical) then replacing the power head, the hose or the wand should not present any ...
17. How do I become a dealer?
    If you are interested in becoming a dealer or distributor, please contact the Regional Sales Manager for your area. To find out who the regional sales manager is for your area, please visit our website at http://www.linearcorp.com/sales_outside.php and click on the link for "Electronic Sales".
18. What is my warranty?
    For a comprehensive look at product warranties, and our return policy, please visit our website at http://www.linearcorp.com/warranty_returns.php.
19. How do I get a return authorization for my product?
    Return authorizations are only given to dealers and/or distributors. If you are an end-user, then you will need to contact a local dealer and have them contact Linear on your behalf. To find a dealer in your area, please visit our website at http://www.linearcorp.com/dealers.php. You can help ...
20. I get suction at my can, but not through inlets.
    If you find that you have good suction at the canister but less than satisfactory at the inlets, you probably have a clog or break in your piping. This is a problem that is best handled by an authorized dealer. To find a dealer in your area, please visit our website at http://www.linearcorp.com/ ...