Linear Products Knowledge Base

Category » e-Merge

There were 175 articles found in this category:

1. How to issue a new card using keyboard entry in eMerge.
   To issue a new card using keyboard entry: Select Administration : People, enter a name and click Search From the Access Cards list on the Access Control tab select <add new>. In the Card Format field select from the drop-down list the card type being issued. Enter the Hot s ...
2. How to assign PIN's in eMerge.
   Assigning PINs in eMerge. Select Administration : People, enter a name and click Search Click on the Access Control tab. In the lower right find the PIN entry box. You can use either 4 or 6 digit PINs. Enter the PIN in this box and click Save. NOTE: This PIN is a required entry at an ...
3. HYow do I remove an access level from a person in eMerge?
   Removing access levels from a person: Select Administration : People, enter a name and click Search Click on the Access Control tab. In the Access Levels section select the access level from the Selected box. Click the left arrow button to move the access level from the Selected ...
4. How do I temporerily disable a card in eMerge?
   To temporarily disable a card: Select Administration : People, enter a name and click Search On the Access Control tab select the card you wish to disable from the Access Cards list. Click to place a check in the Disabled check box and click Apply. Click Save. This card will not ...
5. Lost cards in eMerge.
   Lost Cards Select Administration : Lost Cards. If a card is found and turned in you can determine the identity of the card holder. In the Hot stamp # text box enter the number on the card and click the Search button. If there is no number printed on the card click the Use Reader link and ...
6. How do I specify card/keypad formats in eMerge?
   Specifying Card/Keypad Formats Select Setup : Access Control : Card/Keypad Formats. The Access Control blade supports card readers and keypads that use the Wiegand or Magstripe Track 2 data formats. On this page you can: Create, change, or delete Wiegand card formats. Create, change, or ...
7. About Archive Files
   About Archive Files The system will automatically create archive files of all data required for Custom History Reports and Custom People Reports. Each Sunday, after the full backup at 00:15 hours, the system checks the number of Activity Log records. If this number exceeds 150,000 then all recor ...
8. Access Formats in eMerge.
   Access Card Formats The following card formats are widely used. 26 Bit Wiegand Start Bit Number of Bits Facility Code 2 8 Card ID Number 10 16 Software House 37 Bit Start Bit ...
9. ADA settings for eMerge.i
   You can enter an Extended Time Unlock and Shunt time in seconds. You can also select a Secondary Output and specify a Secondary Active Time for the activation of that secondary output. The extended time and secondary output is for individuals requiring more time or assistance to enter a door ...
10. Backing up the system data in eMerge.
    Backing Up the System Data Select Setup : System Maintenance : Backup System. OR Select Administration : Utility : Backup System. With these pages you can: Back up the security database to ROM and compact flash on the network controller board. Back up the security database to a network a ...
11. Creating and Printing Custom History Reports
    Creating and Printing Custom History Reports Select Administration : Reports : History : Custom Report. On this page you can: Create custom history reports and save them for later re-use. Edit or delete saved custom reports. Run saved custom reports to get output as a tab delimited ...
12. Creating and Printing Custom People Reports
    Creating and Printing Custom People Reports Select Administration : Reports : People : Custom Report. On this page you can: Create custom reports on people and save them for later re-use. Edit or delete saved custom reports. Run saved custom reports to get output as a tab delimited t ...
13. Decoding a card in eMerge
    Decoding a Card Select Setup : Access Control : Utilities : Card Decoder. On this page you can: Decode the bits on Wiegand formatted cards. Decode the bytes on Track 2 of Magstripe cards. Wiegand access cards typically contain a stream of bits that encode the facility code and the encode ...
14. eMerge Log entries.
    Log Entries The following is a complete list of possible activity log entries: Access granted [<reasoncode>] for <username> at <portalname> Access denied [<reasoncode>] by <username> at <portalname> Portal held open at <portalname> Portal ...
15. How do I create a magstripe ABA Track 2 card format in eMerge?
    Magstripe Track 2: Magstripe cards are easily re-programmed and there are no standard magstripe formats for access control. Therefore, you will have to create Magstripe Track 2 formats. You will have to know the specific track 2 format programmed on to your customer's cards. NOTE: The magstripe ...
16. How do I create a Weigand caod format in eMerge?
    To create a new Wiegand card/keypad format: Click the add link under the Name drop-down list. NOTE: If you are adding a card format that is substantially similar to a currently existing format, select the similar format from the drop-down and click clone. Enter a Name for the new format and ...
17. How do I create Access History Reports in eMerge?
    Access History Report Select Administration : Reports : History : Access History. Displays access history based on the query entered. You can enter your query in two ways. In the Query Parameters section you can point and click to build your query. As you point and click your query will be d ...
18. How do I create an access history report in eMerge?
    Access History Report Select Administration : Reports : History : Access History. Displays access history based on the query entered. You can enter your query in two ways. In the Query Parameters section you can point and click to build your query. As you point and click your query will be d ...
19. How do I create history reports in eMerge?
    History Reports Select Administration : Reports : History. History reports can retrieve data from archives when the requested report data is no longer active on the controller board. In version 3.2 the controller maintains an active database of over 100,000 activity log records. Older data is ke ...
20. How do I enable the API for programmatic data exchange between existing personnel systems and security database records?
    API In this section you can enable the API for programmatic data exchange between existing personnel systems and security database records. By default this API interface is disabled. When using API commands the security system uses SHA authentication, and message sequence numbers to ensure the s ...